Sebagai teknisi komputer tentu kita sudah mengenal apa itu BEEP Code. Beep Code merupakan indikator pada sebuah motherboard yang bunyi pada saat sebelum terjadinya Booting Windows. Ada bermacam macam bunyi BEEP, Bunyi Beep terjadi jika motherboard mengalami eror/permasalahan sehingga pada saat melakukan star, Windows tidak bisa Booting.
Bunyi Beep mgnindikasikan eror yang terjadi pada PC System Hardware yang mana Firmware tidak bisa mengeksekusi dikarenakan ada permasalahan yang terjadi pada salah satu perangkat yang ada pada komputer. Berikut merupakan detail singkat Kode Beep dan Kode Digital untuk mengetahui Eror pada PC
Bunyi Beep mgnindikasikan eror yang terjadi pada PC System Hardware yang mana Firmware tidak bisa mengeksekusi dikarenakan ada permasalahan yang terjadi pada salah satu perangkat yang ada pada komputer. Berikut merupakan detail singkat Kode Beep dan Kode Digital untuk mengetahui Eror pada PC
Kode Beep | Keterangan |
---|---|
1 buyi pendek | Eror Ram / Cek Ram |
2 buyi pendek | Cek masing - masing konektor sirkuit |
3 buyi pendek | Ram Failure |
4 buyi pendek | Gagal Seting Waktu |
5 buyi pendek | Proses Gagal |
6 buyi pendek | Eror Keyboard |
7 buyi pendek | Virtual mode exception error |
8 buyi pendek | Gagal membaca Memory |
9 buyi pendek | ROM BIOS checksum failure |
10 buyi pendek | CMOS shutdown Read/Write error |
11 buyi pendek | Cache Memory error |
1 panjang, 3 pendek | Conventional/Extended memory failure |
1 panjang, 8 pendek | Display/Retrace test failed |
1 panjang, 2 pendek | Mengindikasikan VGA card yang tidak terpasang secara benar, atau dikarenakan GA EROR |
Digital Kode | Keterangan |
---|---|
1-1-1-3 | Verify Real Mode. |
1-1-2-1 | Get CPU Type. |
1-1-2-3 | Initialize system hardware. |
1-1-3-1 | Initialize chipset registers with initial POST values. |
1-1-3-2 | Set in POST flag. |
1-1-3-3 | Initialize CPU registers. |
1-1-4-1 | Initialize cache to initial POST values. |
1-1-4-3 | Initialize I/O. |
1-2-1-1 | Initialize Power Management. |
1-2-1-2 | Load alternate registers with initial POST values. |
1-2-1-3 | Jump to UserPatch0. |
1-2-2-1 | Initialize keyboard controller. |
1-2-2-3 | BIOS ROM checksum. |
1-2-3-1 | 8254 timer initialization. |
1-2-3-3 | 8237 DMA controller initialization. |
1-2-4-1 | Reset Programmable Interrupt Controller. |
1-3-1-1 | Test DRAM refresh. |
1-3-1-3 | Test 8742 Keyboard Controller. |
1-3-2-1 | Set ES segment to register to 4 GB. |
1-3-3-1 | 28 Autosize DRAM. |
1-3-3-3 | Clear 512K base RAM. |
1-3-4-1 | Test 512 base address lines. |
1-3-4-3 | Test 512K base memory. |
1-4-1-3 | Test CPU bus-clock frequency. |
1-4-2-4 | Reinitialize the chipset. |
1-4-3-1 | Shadow system BIOS ROM. |
1-4-3-2 | Reinitialize the cache. |
1-4-3-3 | Autosize cache. |
1-4-4-1 | Configure advanced chipset registers. |
1-4-4-2 | Load alternate registers with CMOS values. |
2-1-1-1 | Set Initial CPU speed. |
2-1-1-3 | Initialize interrupt vectors. |
2-1-2-1 | Initialize BIOS interrupts. |
2-1-2-3 | Check ROM copyright notice. |
2-1-2-4 | Initialize manager for PCI Options ROMs. |
2-1-3-1 | Check video configuration against CMOS. |
2-1-3-2 | Initialize PCI bus and devices. |
2-1-3-3 | Initialize all video adapters in system. |
2-1-4-1 | Shadow video BIOS ROM. |
2-1-4-3 | Display copyright notice. |
2-2-1-1 | Display CPU Type and speed. |
2-2-1-3 | Test keyboard. |
2-2-2-1 | Set key click if enabled. |
2-2-2-3 | 56 Enable keyboard. |
2-2-3-1 | Test for unexpected interrupts. |
2-2-3-3 | Display prompt Press F2 to enter SETUP. |
2-2-4-1 | Test RAM between 512 and 640k. |
2-3-1-1 | Test expanded memory. |
2-3-1-3 | Test extended memory address lines. |
2-3-2-1 | Jump to UserPatch1. |
2-3-2-3 | Configure advanced cache registers. |
2-3-3-1 | Enable external and CPU caches. |
2-3-3-3 | Display external cache size. |
2-3-4-1 | Display shadow message. |
2-3-4-3 | Display non-disposable segments. |
2-4-1-1 | Display error messages. |
2-4-1-3 | Check for configuration errors. |
2-4-2-1 | Test real-time clock. |
2-4-2-3 | Check for keyboard errors |
2-4-4-1 | Set up hardware interrupts vectors. |
2-4-4-3 | Test coprocessor if present. |
3-1-1-1 | Disable onboard I/O ports. |
3-1-1-3 | Detect and install external RS232 ports. |
3-1-2-1 | Detect and install external parallel ports. |
3-1-2-3 | Re-initialize onboard I/O ports. |
3-1-3-1 | Initialize BIOS Data Area. |
3-1-3-3 | Initialize Extended BIOS Data Area. |
3-1-4-1 | Initialize floppy controller. |
3-2-1-1 | Initialize hard-disk controller. |
3-2-1-2 | Initialize local-bus hard-disk controller. |
3-2-1-3 | Jump to UserPatch2. |
3-2-2-1 | Disable A20 address line. |
3-2-2-3 | Clear huge ES segment register. |
3-2-3-1 | Search for option ROMs. |
3-2-3-3 | Shadow option ROMs. |
3-2-4-1 | Set up Power Management. |
3-2-4-3 | Enable hardware interrupts. |
3-3-1-1 | Set time of day. |
3-3-1-3 | Check key lock. |
3-3-3-1 | Erase F2 prompt. |
3-3-3-3 | Scan for F2 key stroke. |
3-3-4-1 | Enter SETUP. |
3-3-4-3 | Clear in-POST flag. |
3-4-1-1 | Check for errors |
3-4-1-3 | POST done--prepare to boot operating system. |
3-4-2-1 | One beep. |
3-4-2-3 | Check password (optional). |
3-4-3-1 | Clear global descriptor table. |
3-4-4-1 | Clear parity checkers. |
3-4-4-3 | Clear screen (optional). |
3-4-4-4 | Check virus and backup reminders. |
4-1-1-1 | Try to boot with INT 19. |
4-2-1-1 | Interrupt handler error. |
4-2-1-3 | Unknown interrupt error. |
4-2-2-1 | Pending interrupt error. |
4-2-2-3 | Initialize option ROM error. |
4-2-3-1 | Shutdown error. |
4-2-3-3 | Extended Block Move. |
4-2-4-1 | Shutdown 10 error. |
4-3-1-3 | Initialize the chipset. |
4-3-1-4 | Initialize refresh counter. |
4-3-2-1 | Check for Forced Flash. |
4-3-2-2 | Check HW status of ROM. |
4-3-2-3 | BIOS ROM is OK. |
4-3-2-4 | Do a complete RAM test. |
4-3-3-1 | Do OEM initialization. |
4-3-3-2 | Initialize interrupt controller. |
4-3-3-3 | Read in bootstrap code. |
4-3-3-4 | Initialize all vectors. |
4-3-4-1 | Boot the Flash program. |
4-3-4-2 | Initialize the boot device. |
Digital Code dan Beep Code Pada Motherboard
Reviewed by liee
on
Tuesday, January 01, 2013
Rating:
No comments: